Reader Comments

How to Change Your Key

by Nola Lowerson (2020-05-12)


id="mod_45389024">
This article illustrates how to rekey an Arrow E61 tubular deadbolt as shown below. The principles of rekeying discussed can be applied to most standard pin tumbler type cylinders.








Arrow E61 Deadbolt Source












Overview

Tools required:



Phillips and standard point screwdrivers

Keying kit

Plug follower

A small screwdriver, scratch awl, lock pick or other thin metallic object to act as a poking device

Also required will be a set of keys that have the same keyway as the lock you want to rekey but have different cuts than the key that currently fits that lock.


To Begin:
Tubular deadbolt cylinders are usually small cylinders that are enclosed in rather large outer housings. Therefore you need to remove the lock from the door so that you can access the cylinder. Usually the outer housing is held in place by screws that extend through the turnknob escutcheon on the interior side of the door, however, some locks - like the Arrow D61 deadbolt shown below, are held together by throughbolts that are concealed by the interior turnknob escutcheon. This make little difference except that instead of two screws, on must remove four screws in order to remove the lock.








Partially disassembled Arrow D61 deadbolt, side view. Note how the small screws that hold the interior turnknob escutcheon in place screw directly into hardened steel throughbolts that extend through a hardened steel plate. Source







Hardened steel throughbolts and interior plate, Arrow D61 deadbolt. Source






































Removing the Lock

To remove a single cylinder deadbolt from the door for rekeying, open the door and turn the interior turnknob so that is is out of the way of the screws. Often this will extend the bolt. That's okay. Next, hold the outside housing with one hand while removing the screws from the interior turnknob escutcheon plate with the other. In case these screws are the only fasteners holding the lock together you need to hold the outside cylinder housing so that it does not fall off and become damaged. If this first set of screws only attaches the inside escutcheon but not the entire lock, remove them and the escutcheon and set them down in a safe place. The concealed throughbolts will now be exposed. Usually these take a Phillips screwdriver, but there is no standard as to what head is used on these fasteners. It could be a socket head or Torx screw. You'll find out soon enough. Remember to hold onto that outside housing as you remove the throughbolts.

When you have removed the throughbolts, carefully gather the interior fasteners and exterior housing. Place the mounting parts down in a safe place and bring the outside lock housing with you.

Below is a little video introduction I've made for you about rekeying this type of cylinder.





Rekeying Video





CAUTION

A lock is a spring-loaded device. Spring tension is the force that makes it work. When you rekey a lock you are both working against and working with spring tension to accomplish your task. Here are some of the unfortunate things that can happen:



If you key a 6-pin cylinder to a 5-pin key (as shown in the video) there will be an empty sixth chamber. If, for example, you turn the key before the plug is fully inserted, the 5th pin my drop into that empty sixth chamber. Then you have a real challenge on your hands, getting that top pin out of the plug so you can get the plug out again.

If there is any gap between the plug and the follower, pins may pop out of the bible. The lock will not work right unless you get them back in.

If, when you remove the plug, you find that it contains more than one pin per chamber in the plug, that means that your lock is master keyed. That means that there may be master pins still inside the bible. If you dump a master wafer from the plug and replace it with a bottom pin that is bigger than both put together, you may not be able to insert or remove your key.

Any of these situations could create a lockout situation that would challenge the best of us, and might mean that the lock must be destroyed in order to gain entry.

If you want to read more info in regards to fake locksmith review our own web page. So be careful, and if you feel out of your reckoning, seek the help of a professional locksmith before things get out of hand.
















Arrow E61 Deadbolt tail piece assembly. Source




Rekeying the Cylinder



Remove the cylinder from the housing, if applicable. (Some deadbolts have cylinders that are integral with the cylinder housing. Those cylinders must be rekeyed as they are since they cannot be removed.)

Remove the tailpiece assembly (see parts breakdown above.)

Insert the key that currently works the lock and turn it 90 degrees in relation to the cylinder bible

Remove the plug, following it with a plug follower

Remove the old pins

Remove the old key

Insert the new key

Insert new pins, choosing them so that they are flush with the surface of the plug with the new key inserted

With the key turned 90 degrees in relation to the cylinder bible, use the plug to drive the follower out of the back of the cylinder

When the plug is fully inserted, turn the key so that the cuts align with the bible

HOLDING THE FACE OF THE PLUG IN PLACE WITH YOUR THUMB gently remove the key

Re-install the tailpiece assembly

Test the key










Slightly used cylinder from Arrow D61 deadbolt. Source












Wrap Up

If your key works well and you haven't messed the lock up along the way, go ahead and re-install the deadbolt onto the door. The tailpieces on most tubular deadbolts are timed. Before you start screwing in the fasteners, turn the tailpiece with the turnknob to see if it throws and retracts the bolt smoothly, without forcing the outside housing to turn. If it does, go ahead and tighten down those throughbolts.

With the door closed, check to see that the bolt throws without resistance and the key turns without a hitch. Sometimes locks are installed into crooked holes, so they have a tendency to bind and not work smoothly. This condition can often be amended by repositioning the inside escutcheon or outside housing so that everything lines up correctly.

Once everything is back on the door, try it one more time to make sure it's right. Then you can walk away knowing that no one is going to be locked out because of your work.


I wish you good luck in all your lock adventures.








© 2014 Tom rubenoff



































Related









Home Security

iPhone Controlled Door Locks 3 Amazing Smartphone Deadbolts Have Arrived
by Will Henry1








Crafts & Handiwork

How to Pick a Lock - Guide
by mroconnell23








Door Improvements

Common Hardware for Aluminum Storefront Doors
by Tom rubenoff5








Door Improvements

Which is the Best Keyless Door Lock? Four RFID & Keypad Picks
by Will Henry72








Plumbing

How To Replace a Single Handle Bathtub Faucet Yourself
by Ken Crawford1












Popular









Door Improvements

How to Install a Prehung Door
by Grant Handford2








Door Improvements

Hold-Open Door Hardware
by Tom rubenoff5








Door Improvements

How To Cheaply Repair a Hole in Drywall or a Wooden Door
by Jimmy the jock4


























Comments










Sign in or sign up and post using a HubPages Network account.






0 of 8192 characters used
Post Comment

No HTML is allowed in comments, but URLs will be hyperlinked. Comments are not for promoting your articles or other sites.







sending











AUTHOR
Tom rubenoff

5 years ago from United States


Thanks, Eddy! :)

Thank you, WillStarr.

In the old days all pins were the same length and locksmiths filed them down to fit, however it is not a precise method and almost impossible to do without also incidentally filing the plug, thus simulating years of wear. In short it is like converting a new lock into an old one with a few strokes of a file. I do not recommend it.






WillStarr

5 years ago from Phoenix, Arizona


Excellent! I've noticed that some locksmiths file down a new pin to flush if it's slightly too long. Is that acceptable?






Eiddwen

5 years ago from Wales


Very useful and a great share Tom.

Eddy.